1.5752
2025-03-08 09:05:00 Origin： Remark：0 Click：
Inventory 1.5752 Supplier, Stocklist 1.5752 Chemical, Specification 1.5752 Property steelmaking, Blooming, forging, rolling, heat treatment
TECHNICAL DATA SHEET - W-Nr.1.5752
MATERIAL CATEGORY - Carburizing structural steel
PRODUCT DESCRIPTION
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks.
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF / VD / LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - Quenched and tempered.
MATERIAL SPECIFICATIONS - DIN EN 10084 (1998), DIN 17210 (1986)
CHEMICAL COMPOSITIONS ( mass weight - % )
Carbon, C (％): 0.14 ~ 0.20
Silicon, Si (％): ≤ 0.40
Manganese, Mn (％): 0.40 ~ 0.70
Phosphorus, P (％) ≤: 0.035
Sulfur, S (％) ≤: 0.035
Chromium, Cr (％): 0.60 ~ 1.00
Molybdenum, Mo (％): -
Nickel, Ni (％): 3.00 ~ 3.50
Silicon, Si (％): ≤ 0.40
Manganese, Mn (％): 0.40 ~ 0.70
Phosphorus, P (％) ≤: 0.035
Sulfur, S (％) ≤: 0.035
Chromium, Cr (％): 0.60 ~ 1.00
Molybdenum, Mo (％): -
Nickel, Ni (％): 3.00 ~ 3.50
MECHANICAL PROPERTIES - HOT WORKING, HEAT TREATMENT AND HARDNESS
Hot working temperature / ℃: 1150～850
Heat treatment temperature / ℃ | annealing: 610～650
Heat treatment temperature / ℃ | carburizing: 850～900
Heat treatment temperature / ℃ | quenching (Center): 830～860
Heat treatment temperature / ℃ | quenching (Surface): 780~800 Oil
Heat treatment temperature / ℃ | tempering: 170～200
Hardness after annealing HBS ≤: 230
Heat treatment temperature / ℃ | annealing: 610～650
Heat treatment temperature / ℃ | carburizing: 850～900
Heat treatment temperature / ℃ | quenching (Center): 830～860
Heat treatment temperature / ℃ | quenching (Surface): 780~800 Oil
Heat treatment temperature / ℃ | tempering: 170～200
Hardness after annealing HBS ≤: 230
Size /mm: φ11
After surface hardening |σb/MPa: 1030~1320
After surface hardening |σs≥/MPa: 835
After surface hardening |δ5(％)≥: 9
After surface hardening |ψ(％)≥: 40
After surface hardening |σb/MPa: 1030~1320
After surface hardening |σs≥/MPa: 835
After surface hardening |δ5(％)≥: 9
After surface hardening |ψ(％)≥: 40
After surface hardening |AKV①/J: 55
| size / mm: φ30
| σb / MPa: 930~1280
| σs ≥ MPa: 785
| δ5 (％)≥: 10
| ψ (％)≥: 45
| AKv / J: 55
| σb / MPa: 930~1280
| σs ≥ MPa: 785
| δ5 (％)≥: 10
| ψ (％)≥: 45
| AKv / J: 55
| size / mm: φ63
| σb / MPa: 880~1180
| σs ≥ MPa: 735
| δ5 (％) ≥: 10
| ψ (％) ≥: 45
| AKv / J: -
| σb / MPa: 880~1180
| σs ≥ MPa: 735
| δ5 (％) ≥: 10
| ψ (％) ≥: 45
| AKv / J: -
PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 600mm
Square bar / Flat bar: 10mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Square bar / Flat bar: 10mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 400mm X W100 - 1200mm X L1000 - 5000mm
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, and other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, and other different shapes based on OEM.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners
Process plant – fasteners
Mechanical gears, gear shaft, main axis, valve rod
Mechanical parts - connecting rod, bolt and nut
Multidiameter shaft
Pressure vessel, seamless pipe
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers, E-mail: sales@ccsteels.com
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers, E-mail: sales@ccsteels.com
Hot search：1.5752
Total list
Monthly rank
- 2738NCD4
- 2518X2H4MA
- 21ASTM A739 type B11
- 1824CrMo5
- 16C42
- 1642Cr4Mo2
- 16EN 110
- 1422CrMoNiWV8-8
- 1438XH3MA
- 1340NiSiCrMo7