1.5918
2015-01-23 11:23:04 Origin： Remark：0 Click：
DIN EN 10084 Specifications Carburizing structural steel 1.5918 Round bar, Flat bar, Plate 17CrNi6-6 Stock Available, Hot forging & rolling, Heat treatment
TECHNICAL DATA SHEET - W-Nr 1.5918
MATERIAL CATEGORY: Carburizing structural steel
PRODUCT DESCRIPTION
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - Quenched and tempered.
MATERIAL SPECIFICATIONS - DIN EN 10084 (1998), DIN 17210 (1986)
CHEMICAL COMPOSITION (mass weight - %)
Carbon, C (％): 0.14 ~ 0.20
Silicon, Si (％): ≤ 0.40
Manganese, Mn (％): 0.50 ~ 0.90
Phosphorus, P (％) ≤: 0.035
Sulfur, S (％) ≤: 0.035
Chromium, Cr (％): 1.40 ~ 1.70
Molybdenum, Mo (％): -
Nickel, Ni (％): 1.40 ~ 1.70
Silicon, Si (％): ≤ 0.40
Manganese, Mn (％): 0.50 ~ 0.90
Phosphorus, P (％) ≤: 0.035
Sulfur, S (％) ≤: 0.035
Chromium, Cr (％): 1.40 ~ 1.70
Molybdenum, Mo (％): -
Nickel, Ni (％): 1.40 ~ 1.70
MECHANICAL PROPERTIES - HOT WORKING, HEAT TREATMENT AND HARDNESS
Hot working temperature /℃: 1150～850
Heat treatment temperature /℃| annealing: 610～650
Heat treatment temperature /℃|carburization: 880～980
Heat treatment temperature /℃|quenchingⅠ(center): 830～870
Heat treatment temperature /℃|quenchingⅡ(surface): 780~820, Oil
Heat treatment temperature /℃|tempering: 150～200
Heat treatment temperature /℃| annealing: 610～650
Heat treatment temperature /℃|carburization: 880～980
Heat treatment temperature /℃|quenchingⅠ(center): 830～870
Heat treatment temperature /℃|quenchingⅡ(surface): 780~820, Oil
Heat treatment temperature /℃|tempering: 150～200
HBS≤: 229
|size /mm: φ11
Tensile strength, Rm / MPa: ≥ 1200
Yield strength, Rp0.2 ≥ MPa: -
Elongation, A5 (％) ≥: -
Reduction of area, ψ (％) ≥: -
Impact strength, AKv / J: -
|size /mm: φ30|size /mm: φ11
Tensile strength, Rm / MPa: ≥ 1200
Yield strength, Rp0.2 ≥ MPa: -
Elongation, A5 (％) ≥: -
Reduction of area, ψ (％) ≥: -
Impact strength, AKv / J: -
|σb/MPa: ≥1100
|σs≥/MPa: -
|δ5(％)≥: -
|ψ(％)≥: -
|AKV/J: -
|ψ(％)≥: -
|AKV/J: -
|size /mm: φ63
|σb/MPa: ≥900
|σs≥/MPa: -
|σb/MPa: ≥900
|σs≥/MPa: -
|δ5(％)≥: -
|ψ(％)≥: -
|AKV/J: -
|ψ(％)≥: -
|AKV/J: -
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners.
Process plant – fasteners.
Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut.
Multidiameter shaft, Pressure vessel.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers, E-mail: sales@ccsteels.com
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers, E-mail: sales@ccsteels.com
PRODUCT PROFILE
Round bar / Disc (diameter): 5.5mm to 800mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Disc (diameter): 5.5mm to 800mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 400mm X W60 - 1000mm X L1000 - 5000mm
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, and other different shapes based on OEM.
Pipes / Tubings: OD30 - 1300mm, with wall thickness ranging from 15 to 350 mm.
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, and other different shapes based on OEM.
Pipes / Tubings: OD30 - 1300mm, with wall thickness ranging from 15 to 350 mm.
Test Certificate can be issued by TUV, SGS, BV
Hot search：1.5918
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B