33CrMoV12-9
2015-01-30 09:43:36 Origin： Remark：0 Click：
DIN EN 10085 (2001), DIN 17211 Specification 33CrMoV12-9, Chromium - Molybdenum - Vanadium Base high tensile steel, Round bar, flat bar, and forgings. heat treatment
Official Test Certificate: issued by TUV - SGS - BV
TECHNICAL SPECIFICATION - Grade 33CrMoV12-9
MATERIAL CATEGORY - Carburized structural steel
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
MATERIAL SPECIFICATIONS - DIN EN 10085 (2001), DIN 17211 (1987)
CHEMICAL COMPOSITION (mass weight - %)
Carbon, C (％): 0.29 ~ 0.36
Silicon, Si (％): ≤ 0.40
Manganese, Mn (％): 0.40 ~ 0.70
Phosphorus, P (％)≤: 0.025
Sulfur, S (％)≤: 0.015
Chromium, Cr (％): 2.80 ~ 3.30
Molybdenum, Mo (％): 0.70 ~ 1.00
Vanadium, V (％): 0.15 ~ 0.25
Silicon, Si (％): ≤ 0.40
Manganese, Mn (％): 0.40 ~ 0.70
Phosphorus, P (％)≤: 0.025
Sulfur, S (％)≤: 0.015
Chromium, Cr (％): 2.80 ~ 3.30
Molybdenum, Mo (％): 0.70 ~ 1.00
Vanadium, V (％): 0.15 ~ 0.25
MECHANICAL PROPERTIES - HOT WORKING, HEAT TREATMENT AND HARDNESS
Hardness of Carburized layer |HV: 800
Hot working temperature /℃: 1050～850
Heat treatment temperature /℃|annealing: 680～740
Heat treatment temperature /℃|quenching: 940~980 Oil or Water
Heat treatment temperature /℃|tempering: 600～700
Heat treatment temperature /℃|annealing: 680～740
Heat treatment temperature /℃|quenching: 940~980 Oil or Water
Heat treatment temperature /℃|tempering: 600～700
Heat treatment temperature /℃|carburizing: 500～520
Hardness after annealing HBS≤: 248
Hardness after annealing HBS≤: 248
Size /mm: ≤ 100
Tensile strength, ≥|σb/MPa: 1100
Yield strength, ≥|σs≥/MPa: 750
Elongation, ≥|δ5(％)≥: 10.0
Impact strength, ≥|AKV/J (DVM-V form sampling): 35
Impact strength, ≥|AKV/J (DVM-V form sampling): 35
Size /mm: ≤ 250
TS, ≥|σb/MPa: 1050
YS, ≥|σs≥/MPa: 700
EL, ≥|δ5(％)≥: 12.0
Impact, ≥|AKV/J (DVM-V form sampling): 40
Impact, ≥|AKV/J (DVM-V form sampling): 40
PRODUCT PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 300mm X W60 - 1200mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W10 - 400mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W10 - 400mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, other different shapes based on OEM.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft, Pressure vessel.
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft, Pressure vessel.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers. - Email: sales@ccsteels.com.
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers. - Email: sales@ccsteels.com.
Hot search：33CrMoV12-9
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B