42Cr4
2015-02-02 14:51:00 Origin： Remark：0 Click：
Description 42Cr4 Round bar, flat bar, plate and forgings 42Cr4 Steelmaking, ESR, hot forging, hot rolling, heat treatment, straightened, ultrasonic test, cold working, machined.
Official Test Certificate: issued by TUV - SGS - BV
TECHNICAL SPECIFICATION DATASHEET - Grade DIN 42Cr4
MATERIAL CATEGORY - Flame and high-frequency heating surface hardening steel
PRODUCT DESCRIPTION
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks.
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks.
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treated QT
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treated QT
MATERIAL SPECIFICATIONS - DIN EN 10083-2/3 (2006), DIN 17212 (1972)
CHEMICAL COMPOSITION (mass weight %)
C (％): 0.38 ~ 0.44
Si (％): 0.15 ~ 0.40
Mn (％): 0.50 ~ 0.80
P (％)≤: 0.025
S (％)≤: 0.035
Cr (％): 0.90 ~ 1.20
Mo (％): -
MECHANICAL PROPERTIES - HOT WORKING, HEAT TREATMENT AND HARDNESS
C (％): 0.38 ~ 0.44
Si (％): 0.15 ~ 0.40
Mn (％): 0.50 ~ 0.80
P (％)≤: 0.025
S (％)≤: 0.035
Cr (％): 0.90 ~ 1.20
Mo (％): -
MECHANICAL PROPERTIES - HOT WORKING, HEAT TREATMENT AND HARDNESS
Hot working temperature /℃: 1050～850
Heat treatment temperature /℃|annealing: 680～720
Heat treatment temperature /℃|annealing: 680～720
Heat treatment temperature /℃|normalizing: 840～880
Heat treatment temperature /℃|quenching: 820~850Water, 830~860Oil
Heat treatment temperature /℃|tempering: 540～680
Heat treatment temperature /℃|surface hardening: 820～850
Surface hardness HBC≤: 54~60
Heat treatment temperature /℃|surface hardening: 820～850
Surface hardness HBC≤: 54~60
Size /mm: ≤16
|σb≥/MPa: 980~1180
|σs≥/MPa: 780
|δ5≥(％): 11
|ψ≥(%): 40
|AKV≥/J: 35
Size /mm: 16~40
|σb≥/MPa: 880~1080
|σs≥/MPa: 665
|δ5≥(％): 12
|ψ≥(%): 45
|AKV≥/J: 42
Size /mm: 40~100
|σb≥/MPa: 780~930
|σs≥/MPa: 560
|δ5≥(％): 14
|ψ≥(%): 50
|AKV≥/J: 42
AVAILABLE SHAPES
Round bar / flat bar / strip / forgings / ring
Bright - peeled + polishing, centerless grinding
Forged - ring, tube, pipe casing, discs, shaft
AVAILABLE SHAPES
Round bar / flat bar / strip / forgings / ring
Bright - peeled + polishing, centerless grinding
Forged - ring, tube, pipe casing, discs, shaft
PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 350mm X W60 - 1200mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts, other different shapes based on OEM.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft.
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers, Email: sales@ccsteels.com.
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers, Email: sales@ccsteels.com.
Hot search：42Cr4
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B