DIN 37Cr4
2015-02-07 10:10:03 Origin： Remark：0 Click：
Description 37Cr4 Stocklist, Round bar 37Cr4 Suppliers, Inventory 37Cr4 Ring forging steelmaking, ESR, hot blooming, hot forging, hot rolling, heat treatment, straightened, ultrasonic test, cold working,machined. We also possess advanced precision machining equipments for further processing.
Technical standards - DIN EN 10263-4 (2002), DIN 1654 (1989) or by agreement.
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
TECHNICAL SPECIFICATION DATASHEET - Grade DIN 37Cr4 & W-Nr 1.7034
MATERIAL CATEGORY: Cold heading & cold extruding steel
MATERIAL SPECIFICATIONS: DIN EN 10263-4 (2002), DIN 1654 (1989)
CHEMICAL COMPOSITION (Mass weight - %)
C (％): 0.34 ~ 0.41
Si (％): ≤ 0.40
Mn (％): 0.60 ~ 0.90
P (％)≤: 0.035
S (％)≤: 0.035
Cr (％): 0.90 ~1.20
Mo (％): —
Ni (％): —
Si (％): ≤ 0.40
Mn (％): 0.60 ~ 0.90
P (％)≤: 0.035
S (％)≤: 0.035
Cr (％): 0.90 ~1.20
Mo (％): —
Ni (％): —
MECHANICAL PROPERTIES - Cold heading/Cold extruding steel
Soft annealing temperature /℃: 680～720
Soft annealed (≤100mm)|σb/MPa: 630
Soft annealed (≤100mm)|ψ(％): 58
Cold draw soft annealed (≤60mm)|σb/MPa: 610
Cold draw soft annealed (≤60mm)|ψ(％): 60
Soft annealed (≤100mm)|σb/MPa: 630
Soft annealed (≤100mm)|ψ(％): 58
Cold draw soft annealed (≤60mm)|σb/MPa: 610
Cold draw soft annealed (≤60mm)|ψ(％): 60
Heat treatment / quenching temperature /℃| water quenching: 825~835
Heat treatment / quenching temperature /℃|oil quenching: 835~865
Heat treatment / tempering temperature /℃: 540~680
Heat treatment / quenching temperature /℃|oil quenching: 835~865
Heat treatment / tempering temperature /℃: 540~680
Mechancial after heat treatment
TS, ≥|σb/MPa: 830 - 930
YS, ≥|σs/MPa: 630
EL, ≥|δ5(％): 13.0
RA, ≥|ψ(％): 45.0
TS, ≥|σb/MPa: 830 - 930
YS, ≥|σs/MPa: 630
EL, ≥|δ5(％): 13.0
RA, ≥|ψ(％): 45.0
≥|AKV DVM-V form sampling /J: 41
PRODUCT DESCRIPTION
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
AVAILABLE SHAPES
Round bar / flat bar / hollow bar / sheet
Bright - peeled + polishing, centerless grinding
Forged - ring, tube, pipe casing, discs, shaft
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
AVAILABLE SHAPES
Round bar / flat bar / hollow bar / sheet
Bright - peeled + polishing, centerless grinding
Forged - ring, tube, pipe casing, discs, shaft
PROFILE / DIMENSTION
Round bar / Wire rod (Diameter): 5.5mm to 800mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Wire rod (Diameter): 5.5mm to 800mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T6 - 200mm X W10 - 1500mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W6 - 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W6 - 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners
Mechanical gears, gear shaft, main axis, valve rod
Mechanical parts - connecting rod, bolt and nut
Multidiameter shaft and pressure vessel
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners
Mechanical gears, gear shaft, main axis, valve rod
Mechanical parts - connecting rod, bolt and nut
Multidiameter shaft and pressure vessel
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers, Email: sales@ccsteels.com
If you meet further on any technical enquiry or help, pleased to EMAIL our resident team of qualified production engineers, Email: sales@ccsteels.com
Previous page：W-Nr 1.7033
Last page：1.7034
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B