S96
2015-07-07 09:08:01 Origin： Remark：0 Click：
S96 is Aircraft "S" series alloy structural steel of 2.5% Nickel-Chromium-molybdenum. Round bar, Flat bar Stock S96 Available, Electroslag remelting
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
TECHNICAL DATASHEET - BS S96
MATERIAL CATEGORY - Aircraft "S" series alloy structural steel
TYPE OF STEEL - 2.5% Ni-Cr-Mo steel
MELTING PROCESS - EAF + AOD / + ESR
CHEMICAL COMPOSITION (mass weight - %)
Carbon, C (％): 0.27 ~ 0.35
Silicon, Si (％): 0.10 ~ 0.35
Manganese, Mn (％): 0.45 ~ 0.70
Phosphorus, P (％) ≤: 0.035
Sulfur, S (％) ≤: 0.030
Chromium, Cr (％): 0.50 ~ 0.80
Silicon, Si (％): 0.10 ~ 0.35
Manganese, Mn (％): 0.45 ~ 0.70
Phosphorus, P (％) ≤: 0.035
Sulfur, S (％) ≤: 0.030
Chromium, Cr (％): 0.50 ~ 0.80
Nickel, Ni (%): 2.30 ~ 2.80
Molybdenum, Mo (％): 0.45 ~ 0.65
Molybdenum, Mo (％): 0.45 ~ 0.65
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Condition: Heat treatment
Tensile strength, Rm ≥ MPa: 1180 ~ 1420
Yield strength, Rp0.2 ≥ MPa: 830
Elongation, A5 ≥ (%): 7.0
Yield strength, Rp0.2 ≥ MPa: 830
Elongation, A5 ≥ (%): 7.0
Impact strength, AKv ≥/J: -
Hardness HBS: -
Hardness HBS: -
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - Quenched and tempered.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - Quenched and tempered.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft, Pressure vessel,
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft, Pressure vessel,
PROFILE & DIMENSIONS
Round bar / Disc (diameter): 5.5 to 800mm
Square bar / Flat bar: 6 to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Disc (diameter): 5.5 to 800mm
Square bar / Flat bar: 6 to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 450mm X W50 ~ 1200mm X L1000 ~ 12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W60 - 1200mm X L1000 ~ 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts or other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W60 - 1200mm X L1000 ~ 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts or other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL (sales@ccsteels.com.) our resident team of qualified production engineers.
If you meet further on any technical enquiry, pleased to EMAIL (sales@ccsteels.com.) our resident team of qualified production engineers.
Hot search：S96
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B