23MnNiCrMo5-2
2015-12-16 10:53:07 Origin： Remark：0 Click：
Specification 23MnNiCrMo5-2 datasheet,23MnNiCrMo5-2 Chemical, 23MnNiCrMo5-2 Property from Steelmaking, ESR melted, Blooming, Hot forging, Hot rolling, Heat treatment, Straightening, 100% Ultrasonic test, Cold working or rough turned machining. Technical specification - DIN 17115. We also possess the advanced precision machining equipments for catering for your different special requirements.
Official Test Certificate: issued by TUV - SGS - BV
TECHNICAL DATA SHEET - 23MnNiCrMo5-2 & 1.6541
MATERIAL TYPE - hot rolled bar, wire rod
MATERIAL STANDARDS - DIN 17115
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.20 ~ 0.26
Si (％): ≤ 0.25
Mn (％): 1.10 ~ 1.40
P (％)≤: 0.020
S (％)≤: 0.020
Cr (%): 0.40 ~ 0.60
MATERIAL STANDARDS - DIN 17115
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.20 ~ 0.26
Si (％): ≤ 0.25
Mn (％): 1.10 ~ 1.40
P (％)≤: 0.020
S (％)≤: 0.020
Cr (%): 0.40 ~ 0.60
Mo (%): 0.20 ~ 0.30
Ni (%): 0.40 ~ 0.70
Cu (%): ≤ 0.25
N (%): ≤ 0.012
N (%): ≤ 0.012
HEAT TREATMENT PRACTICE
Normalizing temperature /℃: 860 ~ 900
Quenching temperature /℃: 870 ~ 890 water
Tempering temperature /℃: 400 Min.
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Diameter ≤ /size mm: 50
Mechanical property ≥|σs/MPa: 980
Mechanical property ≥|σb/MPa: 1180
Mechanical property ≥|δ5(%): 10.0
Mechanical property ≥|AkU /J: 40.0
Mechanical property ≥|δ5(%): 10.0
Mechanical property ≥|AkU /J: 40.0
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by IFF /EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / Quenched and Tempered.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by IFF /EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / Quenched and Tempered.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners
Mechanical gears, gear shaft, main axis, valve rod
Mechanical parts - connecting rod, bolt and nut
Multidiameter shaft
Pressure vessel, seamless pipe
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners
Mechanical gears, gear shaft, main axis, valve rod
Mechanical parts - connecting rod, bolt and nut
Multidiameter shaft
Pressure vessel, seamless pipe
PRODUCT PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 600mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 450mm X W60 - 1000mm X L1000 - 12000mm
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
Round bar / Wire rod (Diameter): 5.5mm to 600mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 450mm X W60 - 1000mm X L1000 - 12000mm
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE & SERVICE
If you meet further on any technical enquiry. pleased to EMAIL our resident team of qualified production engineer. E-mail: sales@ccsteels.com
If you meet further on any technical enquiry. pleased to EMAIL our resident team of qualified production engineer. E-mail: sales@ccsteels.com
Hot search：23MnNiCrMo5-2
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B