40NiMoCr10-4
2016-03-31 14:14:57 Origin： Remark：0 Click：
40NiMoCr10-4 is high tensile 1380MPa Alloy Steel 2.5Ni-Cr-Mo Alloy Steel, 40NiMoCr10-4 Round bar, Flat bar, ESR ingot, Hot forging rolling, Heat treatment
TECHNICAL DATASHEET - 40NiMoCr10-4
Official Test Certificate Report: issued by TUV - SGS - BV
MATERIAL CATEGORY - 1380MPa High tensile steel
TYPE OF STEEL - Ni-Cr-Mo Steel
CHEMICAL COMPOSITION (mass weight - %)
Carbon, C (%): 0.36 ~ 0.44
Silicon, Si (%): 0.10 ~ 0.40
Manganese, Mn (%): 0.45 ~ 0.70
Nickel, Ni (%): 2.30 ~ 2.80
Chromium, Cr (%): 0.50 ~ 0.80
Molybdenum, Mo (%): 0.45 ~ 0.65
Phosphorus, P (%): 0.040 max
Sulfur, S (%): 0.040 max
TYPICAL MECHANICAL PROPERTIES
Condition: Heat treatment
Tensile strength, Rm ≥ MPa: 930 ~ 1080
Yield strength, Rp0.2 ≥ MPa: 725
Elongation, A5 ≥ (%): 12.0
Yield strength, Rp0.2 ≥ MPa: 725
Elongation, A5 ≥ (%): 12.0
Impact strength, AKv ≥ J: 28
Hardness HBS: 269 ~ 331
Hardness HBS: 269 ~ 331
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft.
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft.
FORMS AND DIMENSIONS
Round bar / Rod / Disc (diameter): 5.5 to 650mm
Square bar / Flat bar: 10 to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Rod / Disc (diameter): 5.5 to 650mm
Square bar / Flat bar: 10 to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 450mm X W50 - 1000mm X L1000 - 12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts / other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts / other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL (sales@ccsteels.com) our resident team of qualified production engineers.
If you meet further on any technical enquiry, pleased to EMAIL (sales@ccsteels.com) our resident team of qualified production engineers.
Hot search：40NiMoCr10-4
Previous page：ISO 13CrMo4-5
Last page：X9940
Total list
Monthly rank
- 3438NCD4
- 3424CrMo5
- 3119CrNi5
- 2938B3
- 28ASTM A739 type B11
- 2826NiCrMoV11-5
- 2742Cr4Mo2
- 24S135
- 24EN 38
- 22EN20B