ASTM A453 Gr.651A
2016-10-04 14:04:26 Origin： Remark：0 Click：
A453 Gr.651A Sepcifications, ASTM A453 grade 651A Ex-stock, ASTM A453 Gr.651A Suppliers Chemical ASTM A453 Grade 651A Properties from Steel making, ESR melted, Blooming, Forging, Hot rolling, Heat treatment, Straightening,Ultrasonic test,Cold working or Machined. All of these materials conform to Military standard, nuclear power. Technical specification ASTM B453 - 2011.
TECHNICAL SPECIFICATION - ASTM A453 GRADE 651A
TECHNICAL SPECIFICATION: ASTM A453 - 2011
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
MATERIAL CATEGORY: high-temperature bolting, with expansion coefficients comparable to austenitic stainless steel
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.28 ~ 0.35
Si (％): 0.30 ~ 0.80
Mn (％): 0.75 ~ 1.50
P (％) ≤: 0.040
S (％) ≤: 0.030
Cr (％): 18.0 ~ 21.0
Ni (％): 8.00 ~ 11.0
Mo (％): 1.00 ~ 1.50
W (%): 1.00 ~ 1.75
Ti (%): 0.10 ~ 0.30
Nb (%): 0.25 ~ 0.60
Al (%): -
Al (%): -
V (%): -
B (%): -
B (%): -
Cu (%): ≤ 0.50
MECHANICAL PROPERTIES UNDER ROOM TEMPERATURE
Form: rod and bar
Condition: hot-cold worked at 650 Deg min.with 15% min.reduction in cross-sectional area, stress-relief anneal 650 Deg. min. or 4h min.
Form: rod and bar
Condition: hot-cold worked at 650 Deg min.with 15% min.reduction in cross-sectional area, stress-relief anneal 650 Deg. min. or 4h min.
Tensile strength,σb/≥ MPa: 690
Yield strength, σ0.2/≥ MPa: 485
Elongation, δ ≥(％): 18.0
Reduction of area, ф ≥ (％): 35.0
Hardness | HBW: 217 ~ 277
Yield strength, σ0.2/≥ MPa: 485
Elongation, δ ≥(％): 18.0
Reduction of area, ф ≥ (％): 35.0
Hardness | HBW: 217 ~ 277
Hardness | HRC: 29 max.
STRESS RUPTURE REQUIREMENT
Test temperature: 650 Deg.
Stress /MPa: 275 min.
Time to rupture: 100h min.
Elongtation, (%): 5.0 min.
TYPICAL APPLICATIONS
Standard specification for high-temperature bolting, with expansion coefficients comparable to austenitic stainless steel with yield strength ranging from 345 to 827MPa for use in high-temperature service such as fasteners for pressure vessel and valve flanges.
Standard specification for high-temperature bolting, with expansion coefficients comparable to austenitic stainless steel with yield strength ranging from 345 to 827MPa for use in high-temperature service such as fasteners for pressure vessel and valve flanges.
Nuclear reactor
Turbine engine parts - mechanical gears, gear shaft, main axis, blade
Mechanical parts - bolt and nut, fastener
Gas turbine blade
Fuel nozzle
Fuel nozzle
Heat treatment furnace flask and components, especially in the carbonization.
These materials must stand up to high heat, extreme oxidation potential and recycling.
FORMS AND SHAPES
Round bar (Diameter): 5.5mm to 400mm
Square bar / Flat bar: 3mm to 500mm
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
These materials must stand up to high heat, extreme oxidation potential and recycling.
FORMS AND SHAPES
Round bar (Diameter): 5.5mm to 400mm
Square bar / Flat bar: 3mm to 500mm
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL (sales@ccsteels.com) our resident team of qualified production engineers
If you meet further on any technical enquiry, pleased to EMAIL (sales@ccsteels.com) our resident team of qualified production engineers
Previous page：ASTM A453 Gr.660D
Last page：ASTM A453 Gr.651B
