Duratherm 600
2017-09-22 08:53:36 Origin： Remark：0 Click：
Specifications Duratherm 600 datasheet, Duratherm 600 Chemical, Duratherm 600 mechanical properties from Steel making, ESR melted, Hot forging, cold rolling, Heat treated, cold working or Machined.
MATERIAL TECHNICAL DATA SHEET - Duratherm 600
OFFICIAL TEST CERTIFICATE - issued by TUV - SGS - BV
MATERIAL CATEGORY - Cr - Ni- Mo - Co - W Series alloy
CHEMICAL COMPOSITION (WEIGHT %)
C (％): ≤ 0.05
Si (％): 0.20 ~ 0.60
Mn (％): 0.40 ~ 1.10
P (％)≤: 0.030
C (％): ≤ 0.05
Si (％): 0.20 ~ 0.60
Mn (％): 0.40 ~ 1.10
P (％)≤: 0.030
S (％)≤: 0.020
Cr (％): 11.7 ~ 12.3
Cr (％): 11.7 ~ 12.3
Ni (％): Balance
Mo (％): 3.70 ~ 4.30
Co (%): 41.0 ~ 42.0
Co (%): 41.0 ~ 42.0
W (%): 3.60 ~ 4.20
Al (%): 0.60 ~ 0.80
Al (%): 0.60 ~ 0.80
Cu (%): ≤ 0.30
Ti (%): 1.80 ~ 2.20
Ti (%): 1.80 ~ 2.20
Fe (%): 8.50 ~ 8.90
Nb (%): ≤ 0.10
Be (%): ≤ 0.05
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Condition: Solution + Aged treated (750 Deg.)
Tensile strength, σb/≥ MPa: 850 ~ 1100
Yield strength, σ0.2/≥ MPa: 380 ~ 650
Elongation, δ ≥(％): 20.0
Reduction of area, ф ≥ (％): -
Hardness | HBW: 210 ~ 310
Reduction of area, ф ≥ (％): -
Hardness | HBW: 210 ~ 310
TYPICAL APPLICATIONS
Superalloy is widely used to produce the high temperature components for gas turbine in the field of aviation, naval vessels and industry, such as turbine blade, guide blade, turbine disc, high pressure compressor disc, combustor, and also production of energy conversion devices, such as aerospace craft, rocket motor, nuclear reactor, petrochemical equipments, coaly transforming and so on. The alloy is usually produced by AOD / VOD /VIM followed by electroslag refining (ESR) / VAR if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' requirements.
Bars are usually supplied bright surface in the solution annealed condition.
Final heat treatment - solution + Aged
FORMS AND AVAILABLE DIMENSIONS
Round bar (Diameter): 5.5mm to 450mm
Square bar / Flat bar: 3mm to 450mm
Superalloy is widely used to produce the high temperature components for gas turbine in the field of aviation, naval vessels and industry, such as turbine blade, guide blade, turbine disc, high pressure compressor disc, combustor, and also production of energy conversion devices, such as aerospace craft, rocket motor, nuclear reactor, petrochemical equipments, coaly transforming and so on. The alloy is usually produced by AOD / VOD /VIM followed by electroslag refining (ESR) / VAR if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' requirements.
Bars are usually supplied bright surface in the solution annealed condition.
Final heat treatment - solution + Aged
FORMS AND AVAILABLE DIMENSIONS
Round bar (Diameter): 5.5mm to 450mm
Square bar / Flat bar: 3mm to 450mm
Wire rod (Diameter): 0.20 to 13mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: Different shapes based on OEM.
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: Different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our qualified production engineers. -You can reach our sales dept via E-mail: sales@ccsteels.com
If you meet further on any technical enquiry, pleased to EMAIL our qualified production engineers. -You can reach our sales dept via E-mail: sales@ccsteels.com
