Haynes 6B / R30016
2025-02-19 13:57:00 Origin： Remark：0 Click：
Technical specifications Haynes 6B Round bar, Flat bar, plate R30016 AMS 5894 Steelmaking, ESR & VAR technique, Hot forging, Hot rolling, Heat treatment
TECHNICAL DATA SHEET - Haynes 6B & R30016 & AMS 5894
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
MATERIAL CATEGORY: Cr - Co - W Superalloy
CHEMICAL COMPOSITIONS (mass weight - %)
Carbon, C (％): 0.90 ~ 1.40
Silicon, Si (％): ≤ 2.00
Manganese, Mn (％): ≤ 2.00
Phosphorus, P (％) ≤: 0.025
Carbon, C (％): 0.90 ~ 1.40
Silicon, Si (％): ≤ 2.00
Manganese, Mn (％): ≤ 2.00
Phosphorus, P (％) ≤: 0.025
Sulfur, S (％) ≤: 0.015
Chromium, Cr (％): 28.0 ~ 32.0
Chromium, Cr (％): 28.0 ~ 32.0
Nickel, Ni (％): ≤ 3.00
Molybdenum, Mo (％): ≤ 1.50
Cobalt, Co (%): Balance
Cobalt, Co (%): Balance
tungsten, W (%): 3.50 ~ 5.50
Aluminum, Al (%): -
Aluminum, Al (%): -
Copper, Cu (%): -
Titanium, Ti (%): -
Titanium, Ti (%): -
Ferrum, Fe (% ): ≤ 3.00
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Tensile strength, σb ≥ MPa: 900
Yield strength, σ0.2 / MPa: 485
Elongation, δ5 ≥ (％): 5.0
Reduction of area, ф ≥ (％): -
Hardness via heat treatment /HBW: 33 ~ 43
Reduction of area, ф ≥ (％): -
Hardness via heat treatment /HBW: 33 ~ 43
TYPICAL APPLICATIONS
Superalloy is widely used to produce the high temperature components for gas turbine in the field of aviation, naval vessels and industry, such as turbine blade, guide blade, turbine disc, high pressure compressor disc, combustor, and also production of energy conversion devices, such as aerospace craft, rocket motor, nuclear reactor, petrochemical equipments, coaly transforming and so on. The alloy is usually produced by AOD / VOD /VIM followed by electroslag refining (ESR) / VAR if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' requirements.
Bars are usually supplied bright surface in the solution annealed condition.
Final heat treatment - solution + Aged or Double aged.
Superalloy is widely used to produce the high temperature components for gas turbine in the field of aviation, naval vessels and industry, such as turbine blade, guide blade, turbine disc, high pressure compressor disc, combustor, and also production of energy conversion devices, such as aerospace craft, rocket motor, nuclear reactor, petrochemical equipments, coaly transforming and so on. The alloy is usually produced by AOD / VOD /VIM followed by electroslag refining (ESR) / VAR if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' requirements.
Bars are usually supplied bright surface in the solution annealed condition.
Final heat treatment - solution + Aged or Double aged.
FORMS AND DIMENSIONS
Rod, round bar (diameter): 5.50 ~ 450mm
Square bar / flat bar: 8 ~ 350mm
Wire rod (Diameter): 0.10 ~ 16mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 650mm X L (or in coil form)
Forging piece: Different shapes based on OEM.
Steel strip via cold rolled: T0.1 - 3mm X W5 - 650mm X L (or in coil form)
Forging piece: Different shapes based on OEM.
Other sizes can be supplied to meet specific requirements.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our qualified production engineers.
If you meet further on any technical enquiry, pleased to EMAIL our qualified production engineers.
